{
  "scope": "Concept training drafts, not plant operating SOPs",
  "model_id": "CHEM-P204-01",
  "model_version": "0.1",
  "procedures": [
    {
      "slug": "guard-reference",
      "id": "CH-TR-204-01",
      "revision": "DRAFT 0.1",
      "title": "Guard reference and configuration review",
      "model_id": "CHEM-P204-01",
      "model_version": "0.1",
      "status": "Concept training draft \u2014 not an approved plant operating SOP",
      "purpose": "Recognise the correct guard, named retainers and fixed mounting context before rehearsing a maintenance handover.",
      "prerequisites": "Use only the fictional inert model. A task owner must validate source, revision, mechanics and evidence before any real-equipment lesson. This page does not authorize physical work.",
      "steps": [
        {
          "number": 1,
          "title": "Establish the training boundary",
          "action": "Confirm that this is the fictional inert P-204 concept model.",
          "check": "No plant work or operating authority is implied.",
          "components": [
            "P-204"
          ]
        },
        {
          "number": 2,
          "title": "Check the source and revision",
          "action": "Read model CHEM-P204-01 v0.1 and this draft identifier.",
          "check": "The model and procedure versions match.",
          "components": [
            "P-204"
          ]
        },
        {
          "number": 3,
          "title": "Orient the assembly",
          "action": "Locate the blue pump, grey motor and stationary coupling in 3D.",
          "check": "Pump left, motor right; coupling remains stationary.",
          "components": [
            "P-204",
            "M-204",
            "C-204"
          ]
        },
        {
          "number": 4,
          "title": "Identify the correct guard",
          "action": "Select G-204-A and compare its identity with the equipment record.",
          "check": "G-204-A is distinct from the separate G-205-B spare.",
          "components": [
            "G-204-A",
            "G-205-B"
          ]
        },
        {
          "number": 5,
          "title": "Compare the mounting footprint",
          "action": "Orbit the model and inspect the correct guard feet and fixed recessed pads.",
          "check": "All four intended mounting locations are identifiable; geometry is illustrative.",
          "components": [
            "G-204-A"
          ]
        },
        {
          "number": 6,
          "title": "Locate the front pair",
          "action": "Select CG-01, then CG-03, using the part picker or model.",
          "check": "Both front identities are recorded separately.",
          "components": [
            "CG-01",
            "CG-03"
          ]
        },
        {
          "number": 7,
          "title": "Inspect the rear pair",
          "action": "Orbit to inspect CG-02 and CG-04.",
          "check": "A front image is not treated as rear fastening evidence.",
          "components": [
            "CG-02",
            "CG-04"
          ]
        },
        {
          "number": 8,
          "title": "Distinguish retained parts and tools",
          "action": "Inspect the captive groups and separate keyed tool geometry.",
          "check": "No threads, applied torque or continuous tool transfer are claimed.",
          "components": [
            "CG-01",
            "CG-02",
            "CG-03",
            "CG-04"
          ]
        },
        {
          "number": 9,
          "title": "Explore assembly ownership",
          "action": "Use the exploded inspection view to see which parts belong to the guard assembly.",
          "check": "The view is an illustration of grouping, not an approved removal sequence.",
          "components": [
            "G-204-A",
            "C-204"
          ]
        },
        {
          "number": 10,
          "title": "Restore the assembled inspection view",
          "action": "Reassemble the viewer and compare the source again.",
          "check": "Correct guard identity and mounting context remain consistent.",
          "components": [
            "G-204-A"
          ]
        },
        {
          "number": 11,
          "title": "State the review decision",
          "action": "Describe whether the supplied concept references are sufficient for the training example.",
          "check": "Any unverified fit, clearance or retention requirement remains a review item.",
          "components": [
            "G-204-A"
          ]
        },
        {
          "number": 12,
          "title": "Prepare the receiving handover",
          "action": "Link the configuration review to the receiving evidence draft.",
          "check": "Guard review alone is not an operational release or a complete line-up record.",
          "components": [
            "P-204",
            "L-204-D"
          ]
        }
      ],
      "assessment": "Assess identity, front/rear pair recognition and the explanation of source limits. A simulated configuration score does not establish real fastening or readiness.",
      "authoring_status": "Draft for review and future Genesis authoring; not a published Chemicals simulator.",
      "files": {
        "html": "downloads/procedures/ch-tr-204-01-draft-0.1.html",
        "json": "downloads/procedures/ch-tr-204-01-draft-0.1.json",
        "txt": "downloads/procedures/ch-tr-204-01-draft-0.1.txt"
      }
    },
    {
      "slug": "spare-review",
      "id": "CH-TR-204-02",
      "revision": "DRAFT 0.1",
      "title": "Wrong-spare choice, HOLD and reviewed recovery",
      "model_id": "CHEM-P204-01",
      "model_version": "0.1",
      "status": "Concept training draft \u2014 not an approved plant operating SOP",
      "purpose": "Practise a meaningful wrong choice and recover through source comparison rather than forcing a mismatched part.",
      "prerequisites": "Use only the fictional inert model. A task owner must validate source, revision, mechanics and evidence before any real-equipment lesson. This page does not authorize physical work.",
      "steps": [
        {
          "number": 1,
          "title": "Confirm the task context",
          "action": "Identify P-204 and the current concept training draft.",
          "check": "Use the same model/version as the configuration review.",
          "components": [
            "P-204"
          ]
        },
        {
          "number": 2,
          "title": "Locate the expected part",
          "action": "Select G-204-A as the expected coupling guard identity.",
          "check": "The expected ID is explicit before comparing the spare.",
          "components": [
            "G-204-A"
          ]
        },
        {
          "number": 3,
          "title": "Inspect the offered spare",
          "action": "Select G-205-B in the separate tray.",
          "check": "The spare remains separate from the installed guard.",
          "components": [
            "G-205-B"
          ]
        },
        {
          "number": 4,
          "title": "Compare the two footprints",
          "action": "Orbit and compare the visible feet and source identities.",
          "check": "The offered spare has a different mounting footprint.",
          "components": [
            "G-204-A",
            "G-205-B"
          ]
        },
        {
          "number": 5,
          "title": "Make the choice visible",
          "action": "Record that G-205-B is not interchangeable on the supplied concept mounts.",
          "check": "Do not force-fit, snap or silently rename the wrong spare.",
          "components": [
            "G-205-B"
          ]
        },
        {
          "number": 6,
          "title": "Hold the proposed step",
          "action": "Keep the selection on HOLD while the mismatch is unresolved.",
          "check": "No successful-fit or completion state is awarded.",
          "components": [
            "G-205-B"
          ]
        },
        {
          "number": 7,
          "title": "Explain the mismatch",
          "action": "Name the observed ID and footprint difference in the review record.",
          "check": "The reason is concrete, not a generic error message.",
          "components": [
            "G-205-B",
            "G-204-A"
          ]
        },
        {
          "number": 8,
          "title": "Request qualified review",
          "action": "Refer the discrepancy to the task/source owner.",
          "check": "A learner cannot self-approve a different physical part.",
          "components": [
            "P-204"
          ]
        },
        {
          "number": 9,
          "title": "Review the correct training source",
          "action": "Compare the source-checked G-204-A identity and intended mounts.",
          "check": "Only the reviewed training choice is eligible for recovery.",
          "components": [
            "G-204-A"
          ]
        },
        {
          "number": 10,
          "title": "Recover the training decision",
          "action": "Select G-204-A and repeat the configuration review.",
          "check": "The wrong spare remains in its tray; recovery is documented.",
          "components": [
            "G-204-A",
            "G-205-B"
          ]
        },
        {
          "number": 11,
          "title": "Keep independent evidence gaps open",
          "action": "Check whether receiving line-up evidence is supplied.",
          "check": "Correct spare selection does not resolve missing line evidence.",
          "components": [
            "L-204-D"
          ]
        },
        {
          "number": 12,
          "title": "Record feedback for the next rehearsal",
          "action": "Retain the choice, reason, review and recovery in the training record.",
          "check": "The proposed lesson is reviewed before reuse.",
          "components": [
            "P-204",
            "G-204-A"
          ]
        }
      ],
      "assessment": "The critical gate is refusing the wrong-footprint spare. Feedback should name the mismatch, explain the HOLD and permit a source-checked retry; no operational release is scored.",
      "authoring_status": "Draft for review and future Genesis authoring; not a published Chemicals simulator.",
      "files": {
        "html": "downloads/procedures/ch-tr-204-02-draft-0.1.html",
        "json": "downloads/procedures/ch-tr-204-02-draft-0.1.json",
        "txt": "downloads/procedures/ch-tr-204-02-draft-0.1.txt"
      }
    },
    {
      "slug": "receiving-handover",
      "id": "CH-TR-204-03",
      "revision": "DRAFT 0.1",
      "title": "Receiving handover and missing-evidence decision",
      "model_id": "CHEM-P204-01",
      "model_version": "0.1",
      "status": "Concept training draft \u2014 not an approved plant operating SOP",
      "purpose": "Distinguish a maintenance refit record from the evidence the receiving operator needs before a separate authorised release.",
      "prerequisites": "Use only the fictional inert model. A task owner must validate source, revision, mechanics and evidence before any real-equipment lesson. This page does not authorize physical work.",
      "steps": [
        {
          "number": 1,
          "title": "Identify the receiving task",
          "action": "Confirm P-204 and the receiving role in the training scenario.",
          "check": "Maintenance completion and receiving acceptance are separate decisions.",
          "components": [
            "P-204"
          ]
        },
        {
          "number": 2,
          "title": "Check the configuration reference",
          "action": "Match the model, draft and asset identities.",
          "check": "A record for a different asset or revision is not silently accepted.",
          "components": [
            "P-204",
            "M-204"
          ]
        },
        {
          "number": 3,
          "title": "Review the guard record",
          "action": "Read the illustrative configuration review for G-204-A.",
          "check": "Do not infer unshown rear fastening or calibrated torque.",
          "components": [
            "G-204-A",
            "CG-02",
            "CG-04"
          ]
        },
        {
          "number": 4,
          "title": "Locate the discharge reference",
          "action": "Select the fictional L-204-D reference on the model.",
          "check": "The learner can distinguish an identity label from line-up evidence.",
          "components": [
            "L-204-D"
          ]
        },
        {
          "number": 5,
          "title": "Locate the suction reference",
          "action": "Identify the closed L-204-S training stub.",
          "check": "No real flow, isolation or pressure state is asserted.",
          "components": [
            "L-204-S"
          ]
        },
        {
          "number": 6,
          "title": "Ask for the receiving line-up record",
          "action": "Identify the source record required by the task owner.",
          "check": "The scenario intentionally leaves that record missing.",
          "components": [
            "L-204-D"
          ]
        },
        {
          "number": 7,
          "title": "Separate observation and measurement",
          "action": "List which observations are visible and which instrument/inspection records are required.",
          "check": "A camera is not a torque, temperature or continuity instrument.",
          "components": [
            "P-204",
            "L-204-D"
          ]
        },
        {
          "number": 8,
          "title": "Hold the handover decision",
          "action": "Retain HOLD while required line-up evidence is absent.",
          "check": "A completed refit is not used to override this gate.",
          "components": [
            "L-204-D"
          ]
        },
        {
          "number": 9,
          "title": "Escalate the evidence request",
          "action": "State the exact missing record and the responsible reviewer.",
          "check": "The request can be acted on without inventing a reading.",
          "components": [
            "L-204-D"
          ]
        },
        {
          "number": 10,
          "title": "Describe a reviewed recovery",
          "action": "Explain what source-checked evidence and qualified review would be needed next.",
          "check": "This draft does not fabricate a completed receiving record.",
          "components": [
            "P-204",
            "L-204-D"
          ]
        },
        {
          "number": 11,
          "title": "Retain the reasoning",
          "action": "Record the decision, source revision and unanswered questions.",
          "check": "Observation, measurement, review and authorisation remain distinguishable.",
          "components": [
            "P-204"
          ]
        },
        {
          "number": 12,
          "title": "Return a proposed lesson for review",
          "action": "Suggest how the next rehearsal can expose the same evidence gap.",
          "check": "Only an approved training revision is reused; plant release stays outside this example.",
          "components": [
            "P-204"
          ]
        }
      ],
      "assessment": "An independent learner must identify the missing record, retain HOLD and explain the escalation. Treating the refit or an image as sufficient receiving evidence is a critical miss.",
      "authoring_status": "Draft for review and future Genesis authoring; not a published Chemicals simulator.",
      "files": {
        "html": "downloads/procedures/ch-tr-204-03-draft-0.1.html",
        "json": "downloads/procedures/ch-tr-204-03-draft-0.1.json",
        "txt": "downloads/procedures/ch-tr-204-03-draft-0.1.txt"
      }
    }
  ]
}